Відео

I’m sure it’s 10,000 dollars!

The baby bottom hands comment at the end got me laughing my ass off

I like the part where the guy clearly took all the time to set up that table only to trim pre cleaned and partially thawed fish. lol

Price?

I thought about getting one of these until I saw the price. $2,500 for the hot water tank? That’s an exorbitant price for what it is. It is basically a cyclonic burner with coils of tubing and a thermostat. Individually, the components aren’t super expensive, so who’s to say you couldn’t build one yourself? Granted I’m sure the cost is from the high pressure tubing and enclosure, but still for $2,500 just for the burner seems a bit excessive in my opinion. But I guess in certain cases it might be useful if you only occasionally use the hot water function. I have a DeWalt 4400 PSI 4.0 GMP pressure washer with a 13 HP Honda GX390 and it is an absolute beast. Attaching this to a hot water unit would make it the ultimate pressure washer for me. I just wish it wasn’t so expensive.

The instructions are crap ngl its 2024 you guys have to do better with them the only thing specified is the parts lists everything else you have to figure out on your own

Oldschool if it was available. I would havr got it. I just boight one the others day. It will be here tomorrow yaa cant wait

It’s nice because it’s light weight but wish the wheels were all terrain

❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

How do you "deflate" them to store them?

May i use this in bath room tile floorimg to avoid water leakage through tile gaps?

Nincs víz. Villog a piros, de nem indul.

What is price

And mine did at the swivel where the corner of the 90° is. Great idea if it’s not bumpy or hilly terrain but if you have any of that or you accidentally get too close to a tree, there’s too much leverage. I welded mine and then made modification with using half-inch schedule 40 steel pipe, and going from the center of the machine to the arm going to the tractor creating a gusset flatten the ends drilled a hole to match the pens $40 modification

Mine lasted about 2-3 transmission remove replace. Non commercial use. Very NOT impressed. Bought in 2022. Looking for a replacement Ram.

Thank God for this entire program, I hope it has a domino effect.

Discontinued product

Where can I buy this

Very nice

I have the 3/8 and 1/2” impact wrench and for the price I’m very pleased with them both.

Can this be pulling by a small sedan .?

I love this commercial. I spit my coffee out when I first heard it

I like starting and stopping engines at wide open throttle.

Junk

Too bad they don’t sell it anymore

Can this be used for potable water

Hello, I hope you're not angry with me for writing this, but the operating instructions for this device are really good and easy to understand. Most of the questions that arise on the internet can be solved by simply reading the operating instructions. If you do not understand these simple and well-made operating instructions, it is better to stay away from batteries in order not to endanger yourself or others or cause fires. Greetings Robby

it alternates between 12v and orange stanby symbol?

We got ours used for $25 ,maybe one hour of use! Heck of a discount!

Gloves are not long enough,we replaced those and the replaceable protective plastic sheet with heat shrink window plastic. Gloves are $15 and the window film is way less expensive than the $10 for piece stuff they sell. Add a light bar inside and its good to go. Coal slag media is less expensive and does the job well.

The tension spring stays or do you remove it

The 6 foot leaderhose is starting to crackWhere can I get the partsTo change it out

show a video how stun gun used

I have that motorcycle😮

💯🤩👏👏👏

On my 2nd set that never worked out of the box

👏👏👏

I need a new LCD screen for the MP 230sivd LCD welder . Mine got broken somehow and renders this machine useless and I dont know how fo get one. Can anyone help? Thanks

how big of limbs can this consistently cut diameter wise?

Ok. So, how do you use these on a car without it regurgitating?

That shit does not work

I just got this bad boy from Northern Tool today I hope it can last as long as the previous gen I had. My old one still running like day one after more than 10 years 😯

Anyone have a charger they want to sell me

It's dripping and it won't come out. What the over living shit

Bos I no size slewing bearing turun table

I graduated at the Minneapolis school in 2021 and I’m glad to see the younger kids do such hard work!!! Sure with I was still in high school to help my old high school teachers Luther and zac build the awesome go kart

Been on for the last 3 hours and only about 120 gallons are gone

Such an absolutely important program, needs to be implemented country wide. Can't wait to see the reveal. Great job.

Just bought one used but you can't tell it from new very well cared for just lucky i found it on craigslist for a bargain $100 and a 300 mile trip

Worse Gas can ever. Not for the disabled. Not with 5 gallons of fuel. 3 hand operaton.